Arrow SR68206 Uživatelský manuál

* Size rounded off to the nearest footBUILDING DIMENSIONSCAUTION: SOME PARTS HAVE SHARP EDGES. CAREMUST BE TAKEN WHEN HANDLING THE VARIOUS PIECESTO AV

It is important that the entire floor frame be anchored after the building is erected.Below are recommended ways of anchoring. Anchoring Down The Buil

11Remove from bag of screwsand save for the last step67293Weather Stripping (1)5971Roof Beam Bracket (4)66382Lower Door Guide (4)66183Roof Trim Cap(2

Parts List AZ1212Assembly Part Part Quantity CheckKey No. Number Description in Carton List 1 5986 Rear Wall Angle 2 2 6403 Door Track Spl

13Assembly by Key No. I13

The front floor frame is made up ofthree pieces. The rear floor frame ismade up of two pieces. The holes inthese pieces will align when thepieces are

Step 2I1515● Parts Needed For ●Frame AssembliesThe main frame pieces reinforce thewalls. These pieces will later be in-stalled in the center and at th

16Step 3B16● Parts Needed For ●Roof Beam Assembly●●●●● 8474 Roof Beam (1)●●●●● 8476 Side Wall Angle (1)The roof beams join the two gablesand support t

17NOTE:Door Track Splice (painted part)Step 4A17● Parts Needed For ●Door Track Assembly●●●●● 6403 Door Track Splice (1)●●●●● 9366 Door Track (2)66769S

●●●●● Front Floor Assembly (1)●●●●● 8946 Side Floor Frame (2)●●●●● Rear Floor Assembly (1)● Parts Needed For ●Floor FrameStep 5I18The floor frame mus

1 Position a corner panel at thecorner of the floor frame as shown.The widest part of each corner panelmust be placed along the side of thebuilding f

2Owner's ManualBefore beginning construction, check local building codes regarding footings, locationand other requirements. Study and understand

The main frame pieces give rigidity tothe side walls and provide a surfacefor attaching the gables which sup-port the roof.1 Fasten the rear wall ang

Step 8AZ21● Parts Needed For ●Wall Panels●●●●● 8995 Wall Panel (6) Each wall panel has a crimped rib onone side. The crimped rib should gounder the ri

●●●●● 9900 Door Jamb (2)●●●●● 9365 Front Wall Channel (2)● Parts Needed For ●Front Channel/Door JambStep 9A22The door jambs reinforce the dooropening

23The gables go on top of the front andrear walls to support the roof beams.NOTEThe gables are packed nestedtogether and might be mistakenas one piece

● Parts Needed For ●Gables/BracesStep 11A24●●●●● Left Gable Assemblies (2)●●●●● Right Gable Assemblies (2)●●●●● 6635 Gable Brace (2)241 Lift and fast

25Step 12B25● Parts Needed For ●Roof Beams●●●●● Main Roof Beam (1)●●●●● 8474 Roof Beam (2)1 Fasten the main roof beam to thegable brace of the front g

26Step 13I26● Parts Needed For ●Right Roof Panel●●●●● 8468 Right Roof Panel (1)Installing the roof panels is best donewith a step ladder. Begin insta

1 Install a left roof panel at the leftrear and right front corner of the roof.Install a right roof panel at the leftfront corner of the roof.3 Insta

28Step 15B28● Parts Needed For ●Ridge Cap●●●●● 8461 Ridge Cap (1)1 Install the ridge cap on the com-pleted roof section using bolts andnuts. Do not fa

29Step 16B29● Parts Needed For ●Roof Trim●●●●● 8482 Side Roof Trim (2)1 Attach the side roof trim to thelower end of the roof panels on eachside of th

3Selecting and Preparing Your Site: Before assembly, you will want to decide ona location for your building. The best location is a level area with go

30●●●●● 3719 Door Handle Brace (2)●●●●● 10489 Right and Left Doors (2)●●●●● 10497 Horizontal Door Brace (4)●●●●● 9355 Vertical Door Brace (2)●

31Step 18A31● Parts Needed For ●Door Installation & Adjustment●●●●● Right Door Assembly (1)●●●●● Left Door Assembly (1)1 From inside the building,

AnchoringAnchor your building at this time.Floor FrameIf you have purchased a Floor Frame Kit you need to install it at this time.Anchoring and Floor

4Safety precautions are important to follow throughout the construction of your building.•Care must be taken when handling variouspieces of your build

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immedia

ACCESSORIES... A6 WEB6* Some drilling required to fit buildings without mid-wall bracing.Model No. SS404• Makes 8" to 12" (20,3-30,5 c

THIS PAGEWASLEFTBLANKINTENTIONALLY7

THIS PAGEWASLEFTBLANKINTENTIONALLY8

68 3/4"174,6 cmThe Base For Your Building9FRONT(DOOR)FRONT(DOOR)Base I09121"307,3 cm16"/24"40,6 cm/61,0 cm121"307,3 cmOPT